The Wismec Reuleaux RX GEN3 TC Box Mod presents the third generational device of the Reuleaux series, integrating a triple 18650 battery powered chipset capable of an impressive output of 300W in a renovated chassis for a complete all-around device.

The GEN3 mod, is smaller, lighter and more ergonomic than previous versions. Having a large 1.3inch OLED screen and brand-new interface.

A continuation of Wismec's vaulted chipset, the RX GEN3 can fire up to a staggering 300W with comprehensive temperature control and onboard support for Ni200 Nickel, Titanium, and Stainless Steel coil types. In temperature control mode, it features an adjustable TCR mode that allows for expanded compatibility and fine tuning.

• Triple 18650 Battery Platform
• Batteries Sold Separately 
• Wattage Output Range: 1-300W
• Maximum Output Current: 50A
• Minimum Atomizer Resistance: 0.05ohm
• Temperature Range: 200-600F
• Versatile Temperature Control Module
• Supports Ni200 Nickel, Titanium, and Stainless Steel in Temperature Control
• TCR Adjustment Modes
• Preheat Function
• Soft Poly-Angular Frame
• Intuitive 1.3 Inch OLED Display
• Oversized Firing Buton
• Two Adjustment Buttons
• Hinged Battery Door
• Battery Balance Charge System
• Dual Circuit Protection
• Onboard Reverse Polarity Protection
• Upgradeable Software
• MicroUSB Port - Firmware Upgrades
• Spring-Loaded Stainless Steel 510 Connection

In The Box

• 1x RX GEN3 Box Mod
• 1x QC USB Cable
• Instructional Manual

Wismec introduces the Luxotic MF Box. A bottom feeding 100W mod that has interchangeable mod configurations, as well as chipsets.

Out of the box, the Luxotic comes pre-installed with the Variable Voltage chip plus a threaded 7mL squonk bottle and is single 18650 or 21700 battery ready. You can also replace the squonk bottle with the included battery adaptor to run the Luxotic in dual 18650 configuration.

The 0.91" OLED screen displays wattage output, atomiser resistance, voltage output, amperage output and single battery life indicator.

• Proprietary Avatar Circuit Board
  • Variable Wattage Mode
  • 100W Maximum Output
  • Temperature Control Mode
  • 200 to 600 Degrees Fahrenheit Range
  • Compatible With
    • Ni200
    • SS316
    • Ti10
  • M1/M2/M3 Memory Modes
• Bottom Fed Mode and Box Mod Mode
  • Bottom Fed Mode
    
    • Threaded Silicone Bottle
    • 7mL Maximum Capacity
    • Magnetic Access Door
    • Magnetic Squonk Button Panel
  • Single or Dual 21700/18650 Battery Powered
    • Tool-less Battery Door Cover
    • 18650 Battery Adapters Included
      • One Hard Plastic Adapter
      • One Soft Silicone Adapter
    • Dual Battery Mode
      • Attach Dual Battery Adapter
    • Batteries Sold Separately
• Three Button Control Face
  • Oversized Firing Button
  • Dual Adjustment Buttons
• 0.91 Inch OLED Screen
  • Power Output Display
  • Voltage Output Display
  • Atomiser Resistance
  • Amperage Output Display
  • Single Battery Output Display
• Over-charge Protection, Over Discharge Protection, 10 Second Firing Protection, Reverse Polarity Protection, Over-Current Protection, Temperature Protection, and Short-Circuit Protection

Dual Battery Configuration: Batteries must be matched in brand, model and battery state at all times. Discharge and recharge batteries within the same grouping of two. Failure to do so may result in injury. Never use damaged or improperly wrapped batteries.

The Wotofo x Mike Vapes collaboration brings you the Recurve 80W Squonk Mod. A semi-mechanical, incredibly ergonomic mod that fits snug into anyones hand. The Recurve Squonk Box mod is made with a combination of zinc alloy and a rubberised coating that blends it smooth and curvy lines with a comfortable texture that makes it excellent for all day use.

Compatible with single 18650, 20650, and 2X700’s with two seperate battery adapters to accommodate for varying sizes.

The Recurve has a resistance range of 0.08Ω - 3.0Ω that will automatically adjust wattage output based on remaining battery charge.

Featuring a magnetic panel covering the 8mL bottom feed bottle, this allows for mess free removal and refilling without disrupting your battery. There is an LED light strip indicator located behind the squonk bottle in order to indicate various states of the device. The LED light will stay on during charging and will turn off once the battery is at maximum charge. The Recurve supports 2A on board charging, but we recommend for ensuring safety and longevity of your batteries to charging externally.

Product Specifications:

• Proprietary Chip
  • Power Output Based on Current Battery State
  • 80W Maximum Output
  • 3.2 to 4.2V Output Voltage
  • 0.08 to 3.0Ω Atomiser Range

• Bottom Feed Bottle
  
  • 8ml Maximum Capacity
  • Knurled Delrin Cap
  • Removable Magnetic Panel

• LED Light Indicator
  • Behind Squonk Bottle
  • Blinks 5 Times To Indicate Short Circuit
  • Blinks 10 Times To Indicate Low Voltage
  • LED Light Stays On To Indicate Overheating
  • Blinks Once To Indicate No Atomiser Detected
  • LED Stays On When Charging And Turns Off At Full Charge
• Single 18650/20650/20700/21700 Battery Powered
• Removable Magnetic Battery Panel
• Battery Sold Separately

• Single Button Control Face
  • Oversized Firing Button

• Micro USB Charging
  • 2A Max Charge Rate

• Rubberised Zinc Alloy Construction

• PCB Circuit Board
  • Short Circuit Protection
  • Low Voltage Protection
  • Overheating Protection
  • 10 Second Auto Cutoff Protection
  • Reverse Polarity Protection
  • Over Charging Protection
  • Over Discharging Protection

Enter the dragon with this innovative new design from Uwell - now available in New Zealand!

The Uwell Nunchaku lets you vape like a ninja with its sleek, discreet design that hides away with ease and packs a serious punch. This device is loaded with features including a proprietary chipset allowing for V/W mode (5w - 80w), temperature control mode (Ni, SS), and bypass mode.

With the power of an 18650 external battery, the convenience of on-board USB charging, and a maximum direct output of 7 volts the Nunchaku is an absolute weapon making it a must have for any vape warrior.

• Power range: 5-80W
• A new generation of e-cigarette control panel by Uwell independent R&D, makes the tube as safe as a box mod.
• Multiple work modes: power mode, TC mode (NI,SS), bypass mode.
• Requires one replaceable high-drain 18650 battery (sold separately).

The Tesla Invader IV 280W Mod has arrived at The Vape Shop NZ. With the massive success of its predecessor, TeslaCigs have released their new, lighter VV Tesla Invader IV. Now compatible with dual 21700, 20700 or 18650 batteries, essentially improving the potential battery life, while retaining the same performance of high drain 18650s. 

The Invader series are an incredibly durable range of mods that are built to last. With more range of power on the 5 step potentiometer and increased resistance range, the Invader IV is able to run between 3-8 volts and down to 0.08Ω.

The highly anticipated Tesla Invader IV is one of the most reliable, hard hitting mods on the market. While the Invader IV hits like a series mechanical mod, it still has the safety features of a standard regulated mod without all the bells and whistles getting in your way. 

With incredible efficiency and no nonsense design, the Tesla Invader IV is the perfect choice for people who want unadulterated power and ease of use. The  The Invader IV has a maximum power output of 280W, and fires down to a super low 0.08ohm. The Invader IV also supports USB input charging, so you don't need to rely on an external charger to charge your batteries.

We advise a thorough understanding of ohm’s law for using this variable voltage device. You will need to calculate the correct voltage to achieve the wattage level that your coil/s require.

• Dimension: 92 x 60 x 28mm
• Material:  Aluminium alloy
• Cell Type: Two high-drain 18650/20700/21700 cells
• Maximum Output Wattage: 280W
• Voltage Adjust: I-V level
• Output Voltage Range: 3-8V
• Maximum Output Current: 53A
• Resistance Range: 0.08ohm-3.0ohm
• Input Voltage Range: 6.4V-8.4V
• Standby Current: <50uA 
• USB: 5V/1.5A
• LED Indicator: Blue-Green-Red
• Protections: Over puffing protection, reverse connection protection, atomizer short-circuit protection, low voltage alert, overheat protection, over-current protection 
• Thread: 510

In The Box

• 1x Invader IV Mod
• 1x USB Cable
• 2x 18650 Adapters 
• 1x Information Card

Introducing Vaporesso's latest powerhouse to NZ - the Armour Pro. Beautiful, sophisticated, and elegant, the Armour Pro's clean lines and simplicity belie a powerful Omni Board 4.0 chipset capable of a maximum output of 100W.

A 0.96 inch colour screen displays essential information to the user, such as: wattage/temperature, atomiser resistance, and individual battery life display. The screen itself is built into the firing button and blends seamlessly into the Armour Pro's luxurious form and function.

The Armour Pro is powered by a single 18650 battery, or can also utilise 20700/21700 batteries for users requiring extended battery life. The advanced Omni Board 4.0 chipset features six different output modes, multiple protection systems, and can utilise 2A quick charging - no need to wait all day for your batteries to charge!

With an incredible 0.002s firing speed and a total atomiser resistance range of 0.03 - 5.0Ω, the Armour Pro will have you enjoying pure, rich flavour and smooth, silky clouds all day!

• 5 to 100W Output
  • OMNI Board 4.0
    • Six Total Output Modes
    • Insta-Fire
      • 0.002 Second Firing Speed
    • Super Player Mode
      • 0.03 to 5.0Ω Atomiser Resistance Range
  • 0 to 8.5V Voltage Range
  • Smart VW
    • Automatically Recommend Ideal Output
    • Can Easily Adjust
  • Customised Curve of Wattage (CCW)
    • Customise Wattage Output By Second Increments
    • Customise Ramp Up by 0.5 Second Increments
  • Customised Curve of Voltage (CCV)
    • Customise Voltage Output By Second Increments
  • Bypass Mode
  • Firmware Upgradeable
• Temperature Control Suite
  • Ni200 Nickel Support
  • Titanium Support
  • SS316 Support
  • Customized Curve of Temperature (CCT)
    • Customize Temperature Output Over Time
  • TCR Mode
  • 200 to 600 Degrees Fahrenheit
  • Atomiser Lock
• Magnetized Battery Bay Access
  • Single 21700/20700/18650 Battery Powered (sold separately)
• Sleek and Beautiful Chassis Design
  • Futuristic Styling
• Four Button Control
  • Oversized Firing Button
    • Screen Integrated Into Firing Button
  • Angular Adjustment Buttons
  • Mode Button
• 0.96" Inch TFT Display
  • Temperature Mode and Output
  • Output Power
  • Atomiser Resistance
  • Individual Battery Life Indicator
    • Remaining Charging Time (RCT)
  • Puff Counter
• 2A Quick Charge System
  • Remaining Charging Time
  • Equalising Charge System
  • USB Input Protection
• Micro USB Charging Port
• In-Mould Labeling (IML) Injection Coating and Aluminum Alloy Chassis
• Spring Loaded Gold Plated 510 Connection
• Burn Protection/Overtime Protection/ Overcharge Protection/ No Load Protection/ Low Resistance Protection/ ESD Circuit Protection/ Short-Circuit Protection/ Low Power Protection/ Pass-Through Protection

Desire Designs collaboration with OhmBoyOC, the Rage 155W Squonk mod has arrived at The Vape Shop NZ. A dual 18650 powered squonk box mod with a maximum output of 155W, sophisticated and classy design, temperature control suite, and a quarter turn and pull 7mL squonk bottle.

The Rage Squonk has a three button design with an intuitive mounted display screen that displays the essential factors that vapers need to see. A solid stainless steel 510 connector with spring loaded gold plated center squonk pin for optimal conductivity. Supporting Nickel, SS316, Titanium, and Bypass mode

The high amperage 18650 batteries are housed through the magnetic battery door of the Rage Squonk, the 7ml squonk bottle is housed on the front of the device and can be removed by a small notch, atop the squonk bottle features a knurled threaded cap.

The Ohm Boy X Desire Rage Squonk 155W is a phenomenal device to pick up for the pure power and the aesthetically pleasing look and feel.

Please Note: Batteries must be matched in brand, model and battery state at all times. Discharge and recharge batteries within the same grouping of two. Failure to do so may result in injury. Never use damaged or improperly wrapped batteries. 

• 5 to 155W Output Range
  • 0.08 to 3Ω Atomiser Range
  • 40A Max Output Range
• Temperature Control Suite
  • Ni200 Nickel Support
  • Titanium Support
  • SS316 Support
  • Bypass Support
  • 200 to 600 degree Fahrenheit Range
• 0.69 inch Mounted OLED Screen
  • Diagonal Arrangement
  • Output Temperature
  • Output Wattage
  • Output Voltage
  • Material and Mode Selection
  • Atomiser Resistance
  • Output Current
  • Battery Life Indicator
  • Screen Flip
• 7mL Squonk Bottle
  • Quarter Turn Pull
  • Knurled Top
• Three Button Control Face
  
  • Oversized Firing Button
• Magnetic Battery Door
  • Accepts Dual High Amperage 18650
    • Batteries Sold Separately
  • USB Port
    • Update
    • Charge up to 1A
• Stainless Steel Plated 510 Threading and Firing Pin
  • Spring Loaded Gold Plated Center Pin
• Short Circuit Protection/ Over Charging Protection/ Auto Lock Protection/ Low Voltage Protection/ Over Vaping Protection

1x Micro USB Cable
1x Manual and Warranty Card

The Innokin Proton mod has just arrived to The Vape Shop NZ. The Proton is a 235 watt high-performance box mod with a first of its kind joystick style selector and 1.45” TFT colour screen display which supports 6 colours.

Unlike anything you’ve seen from Innokin, every component, texture, and material of Proton underwent a complete design overhaul to bring you not only the high quality you expect from Innokin but the innovation factor that stems from its namesake as well. 

In short, the Proton is all about customisation and user experience. It’s quality made affordable.

• 6 to 235W Wattage Output
  • 0.05 to 3.5Ω Atomiser Resistance Range
• Temperature Control Suite
  • Ni200 Nickel Support
  • Titanium Support
  • Stainless Steel Support
  • Curve Support
  • TCR Support
  • Bypass Support
  • 300 to 600 Degrees Fahrenheit Output Range
• 1.45" TFT Screen Display
  • Output Wattage or Temperature
• Output Timer
• Output Voltage
• Mode and Heating Element
• Individual Battery Life Indicator
• Atomiser Resistance
• Lock Indicator
• Puff Counter
• Six Menu RGB Customisation
  • Blue
  • Red
  • Green
  • Pink
  • Purple
  • White
• Dual Control Interface
  • Oversized Grip Style Fire Button
  • Analog Control Adjustment Interface
• Slide to Open Bottom Latch Battery Access Door
  
  • Accepts Two High Amperage 18650 Batteries
    
    • Sold Separately
  • Micro USB Charging
    • 5V/2A
• Stainless Steel 510 Threading
• 24K Gold Plated Spring Loaded 510 Connection

Proton Mod Dimensions

• 85mm by 44.6mm by 29.6mm

First to stock in NZ, The Vape Shop is proud to introduce the Lost Vape Triade DNA250C. An ultimate representation of Evolv's latest DNA250C chipset, a modern and futuristic edition of the triple 18650 structural architecture with close attention to details in designs and craftsmanship.

The chassis features similar aesthetics to its predecessor, the luxurious carbon fibre wrapped battery bay provides a streamlined and universally elegant design, while clean angles and faces tie the aesthetic look together. Precision milled stainless steel buttons retain the highly responsive and smooth feel, while adding ventilation stripes for a perfect statement piece.

The Triade DNA250C integrates Evolv's most powerful DNA250 colour chipset that implements a host of innovative functionality - replay function, boost mode, wattage control, temperature protection, preheat and an onboard programmable multi-colour LED.

Powered by triple 18650 batteries, the Triade can fire up to a staggering 300W. Fully upgraded in performance while retaining the pinnacle of designs in reconfigurable devices, the Lost Vape Triade DNA250C is the ultimate flagship output technology.

Please Note: Batteries must be matched in brand, model and battery state at all times. Discharge and recharge batteries within the same grouping of three. Failure to do so may result in injury. Never use damaged or improperly wrapped batteries.

• DNA250C Chipset
  • Official Evolv Chipset
  • 1 to 300W Output
  • Boost Mode
    • Increases Initial Power Output and Ramp-Up Time
  • Escribe Compatible
• Temperature Control Suite
  • Ni200 Nickel Support
  • Titanium Support
  • Stainless Steel Support
  • Additional Settings Configured Through Escribe
  • 200 to 600 Degrees Fahrenheit
• Triple 18650 Platform
  • Gold Plated Spring Loaded Contacts
  • Batteries Sold Separately
• Carbon Fibre Panels
• Four Button Control Face
  • Oversized Firing and Adjustment Buttons
  • Rectangular Adjustment Buttons
• 0.9 Inch Full Color TFT Screen
• Displays Essential Data Neatly
  • Check Atomiser
  • Shorted
  • Weak Battery
  • Check Battery
  • Temperature Protected
  • Ohms Too High/Too Low
  • Too Hot
• Adjustable via Escribe
• Replay Function
  • Capture the Perfect Puff
  • Select or Tune Preferred Temp Control
    • Nickel 200
    • SS
    • Titanium
  • Temp-Sensing Coils
    • Mix and Match Different Coils
      • Example. Ti Wrapped with SS
  • Combinations of None Temp Coils and Temp Coils
    • Example. Kanthal Wrapped with Ti
• Escribe Companion Software
• Configure and Modify the operation of the DNA250C
• Escribe Download Link
• Escribe Interactive Training Course
• Micro USB Port
  • 2A Charging
  • Firmware and Software Upgrade
• USB On-The-Go
  • Triade DNA250C Acts as a Power Bank
• Stainless Steel 510 Thread Point
  • Nickel Plated Brass 510 Contact

DNA250C Features

• 1 to 300W Output Range
• .2 to 10.0V Output
• 0.1 to 2.0Ω Kanthal Resistance Range
• 0.08 to 1.0Ω Temperature Sensing Range
• Temperature Range
  • 200 to 600 Degrees Fahrenheit
• Cell by Cell Monitoring
• Cell Balancer
  • 2A USB Charger
• Atomiser, Weak Battery, Temperature, Resistance, Auto Power Down, and Heat Protection
• Escribe
  • Configure and Modify the operation of the DNA250C
  • Escribe Download Link
  • Escribe Interactive Training Course
• Autosensing Temperature Resistance
• Lock Mode
• Stealth Mode
• Power Lock Mode
• Power Preset Mode
• Resistance Lock
• Max Temperature Adjustment
• Efficiency
  • 98%
• Screen On Current
  • 21mA
• Quiescent Current
  • 3.5mA
• Power Down Current
  • 5uA

1x Lost Vape Triade 250C Box Mod
1x User Manual
1x USB Cable
1x Male to Female USB Cable

The Zenith 3 is the latest dual 20700 battery semi-mechanical box mod to land in NZ. Presenting with a unique easy to grip shape with hard lines and gorgeous colour accents, it features a voltage adjustable knob with 16 voltage levels from 2.4V-6.9V.

The Zenith 3 box mod’s chipset is designed by IWEPAL and features short circuit protection, low power protection, reverse battery protection and has milliseconds fire speed with a maximum output of 300W and 50A discharge.

The device is simple to operate, no overhang with large atomisers, supports USB charging, and is compatible with 20700 batteries for longer life. An 18650 battery adapter is included. 

• Max Wattage: 300W
• Size: 92*49*34.5mm 
• Dual 20700 batteries mod with long battery life
• Semi-mechanical High power Box Mod
• 360 degree Adjustable Voltage Knob
• 16 voltage levels to adjust from 2.4-6.9V
• Screenless Design - Efficient Battery Use
• Various protection
• Large side fire button
• Resistance Range: 0.05~3.0 ohm
• USB port charging support

From ergonomics to ease of use, nothing fits in your hand and performs like the Baby Ness.

Based off the highly sought after stabilised wood mods, the originals would sell on auctions for $5,000-$8,000. We are excited to bring you the same amazing experience, at a fraction of the cost.

As its predecessor, the Baby Ness shares a similar appearance with the Loch Ness. But the Baby Ness is compatible with 21700, 20700 and 18650 batteries, bringing a large range of cell selection. 

Simplicity and function are at the forefront of this offering. The ease of use and rock-solid design make this a winner. The mod will easily accept a 26mm atomiser without overhang so your atty options are endless.

Venvii is yet again producing a simple, elegant and above all solid performing mod. It does exactly what it is supposed to do without flashing lights and speedometers.

• Ergonomic design for comfortable grip
• Various battery protections
• Tri-button design for easy operation
• 2A quick charging
• Firmware upgradable
• Dimensions: 90 x 42 x 30mm
• Temperature range: 200–600℉ / 100–300℃
• Wattage range: 5-80W - 18650, 20700 cell, 5-120W - 21700 cell
• Supported resistance range: 0.05-2.0Ω 
• Voltage output range: 0.5-8.5V
• TC modes: Ni200/titanium/tungsten/SS304/SS316/SS317/TCR/TFR
• Wattage Mode: boost(preheat), smooth, curve, normal
• Battery: 1x 21700 cell (discharging current should be above 40A) / 1x 20700/18650 cell (discharging current should be above 35A) (not included)

Warning: Only use high-discharge batteries in the Baby Ness. Battery specifications must be able to handle the high output load. You must select the correct output setting in relation to the battery you are using in the device, 35A+ for 18650 / 20700 and 40A+ for 21700 mode. Do not use batteries above the manufacturer recommended rated output as it can cause damage or even failure to the battery and result in fire or explosion.

In The Box
1x Venvii Baby Ness 120W
1x 18650 Battery Adapter
1x User Manual

Geekvape's nigh on indestructible Aegis Legend 200W Mod has landed in New Zealand!

IP67 waterproof and dustproof, MIL STD 810G-516.6 military grade shockproof means the Aegis Legend is water, dust, and shock resistant. The ultimate choice for users looking for a highly durable and powerful box mod.

Powered by two 18650 batteries (not included), and the advanced AS chipset, the mod features up to 200w of power and a fast, accurate, and adjustable colour display.

The Aegis Legend is fabricated from high-quality, durable materials including stainless steel powder metallurgy, zinc die casting alloys, die casting aluminium, 40hrc carbon steel, LSR silicone, and leather. Enabling the device to be able to withstand drops, water immersion, and dirty environments, and to be easily cleaned. 

Dimensions: 90.5 x 58 x 30.6mm
MAX power output: 200W
Output mode: VW/VPC/TC/TCR/BYPASS/VPC
Resistance range: 0.05-3.0Ω
Material: Aluminum + Zinc alloy + Silicone
Battery: 2x 18650 cells (not included)
Temperature Range: 100-315℃/200-600℉
IP67 waterproof and dustproof; MIL STD 810G-516.6 military grade shockproof

The latest All-In-One (AIO) device from Aspire, The Breeze 2 has arrived in NZ!

The Breeze 2 takes AIO devices to a much-improved level. With the success of the original Breeze, Aspire has redesigned their MTL starter kit with a longer lasting 1000mAh internal battery, revamped refillable pod cartridge and adjustable airflow. Thus moving the Breeze 2 into the mouth to lung, restricted and direct lung inhale categories.

U-Tech coil technology achieves the most flavourful vapour from a pod system and the included 1.0Ω coil is perfect for nicotine salts use. A dark-tint replaceable pod means monitoring your juice levels couldn’t be easier.

The combination of a high performance coil system, ultra compact form factor and simplicity makes the Aspire Breeze 2 a great on-the-go device!

Purchase additional coils here: Aspire Breeze 2 Replacement Coil Pack
Purchase additional replacement cartridges here: Aspire Breeze 2 Replacement Pod & 0.6Ω Coil  // 3mL

• All In One System
  • Single Fire Button Operated
  • Integrated 1000mAh Internal Battery
    • Micro USB Charged
    • 800mA Maximum Charge
  • 3.0mL Tank Reservoir
    • Top Filled
    • Breeze U-Tech 0.6Ω Coil
    • Breeze U-Tech 1.0Ω Coil
      • Used for Salt Based Nicotine E-Liquids
    • Adjustable Airflow
      • Located When Removing Mouthpiece
      • Knurled Design
    • Clear Tank Reservoir
• Direct Voltage Output
  • Bases on Battery State
• Compact Profile
  • 19mm by 35mm by 96mm
  • Perfect for Travel and Commuting
  • Easily Fits Within Shirt Pocket
• Multi Use Top Cap
  • Acts as Drip Tip
  • Access Coil
  • Protective Cap
• LED Battery Life Indicator
  • Blue/Orange
    • 4.2V to 3.8V
  • Blue
    • 3.7V to 3.4V
  • Orange
    • 3.3V to 3.0V
• Aluminum Alloy Construction
  • PEPG Tank Section

4x Extra O-rings
1x Silicone Seal
1x Micro USB Charging Cable
1x User Manual

After much anticipation the VandyVape x Tony B Pulse BF 80W Box Mod has hit The Vape Shop NZ stores!

Following the huge success of its unregulated predecessor, this 80W mod is sure to please squonk mod lovers. Updated with VandyVape’s proprietary Vandy Chip and also a larger 8mL squonk bottle, we have some good feelings about this device!

Available in an array of different colours, including four beautiful coloured resin styles and two sleek carbon fibre designs with magnetic doors, this will be sure to look good in anyone’s hand!

The powerful Vandy Chip offers high-efficiency and high-accuracy including overheating, overcurrent, short circuit, open circuit, overtime, and reverse polarity protection; and also features a low battery warning.

Compatible with both 18650 and 20700 batteries (sold separately).

Specifications

• Size: 54 x 25.9 x 82 mm
• Max wattage output: 80 watts
• Connection threading: 510

In The Box

• Vandy Vape Pulse BF 80W Box Mod
• 8 mL Squonk Bottle
• QC USB Cable
• Instructional Manual
• 18650 Battery Adapter

Geekvape's greatest has arrived in New Zealand!

The Blade is a behemoth of a mod. Sporting two 21700, 20700 or 18650 batteries (not included) this device has what it takes to run big power all day. Capable of a whopping maximum output of 235 watts and constructed with aircraft grade PPS this is one of the beastliest mods on the market today.

With a design inspired by the classic works of Van Gough and all the features and functions you want including V/W mode (235w max), temperature control, bypass mode, and an illuminated fire button and LED display, this device is the perfect blend of classic styling and modern technology.

Size: 93 x 52 x 38mm
Battery Type: 2x 18650(with adapter)/20700/21700 Battery (Not included)
Power Range: 5-235W
Material: Aircraft-grade PPS
Resistance Range: 0.05-3.0ohm
Working Modes: Power/TC/TCR/VPC/BYPASS
Thread: 510 thread

Lost Vape's Mirage DNA75C has just landed in NZ! A full revitalisation of all previous Lost Vape mods, the Mirage features the latest Evolv DNA75C Colour Chipset with built in Escribe software and upgradeable firmware. Housed in a luxurious chassis crafted from anodised aluminium, each device features a beautiful resin finish resulting in a unique and striking design that is sure to turn eyes.

The Mirage is capable of 75W maximum output, a full temperature control suite, and can utilise a single 18650, 20700, or 21700 battery (sold separately). The control face features a 0.96 inch Full Colour TFT Screen which displays essential data within a customisable user interface, and has three adjustment buttons along with the firing button.

With the advanced DNA75C Chipset and exquisite craftsmanship, the Lost Vape Mirage is one of the highest quality mods currently available on the market.

• DNA75C Chipset
  • Official Evolv DNA75C Colour Chipset
  • 1 to 75W Output
  • 30A Maximum Continuous Output
  • Built In Escribe Software
• Temperature Control Suite
  • Ni200 Nickel Support
  • Titanium Support
  • Stainless Steel Support
  • 200 to 600 Degrees Fahrenheit
• Single 18650/20700/21700 Platform
  • Gold Plated Spring Loaded Contacts
  • Bottom Latch Battery Door Panel
  • Batteries Sold Separately
• Four Button Control Face
  • Oversized Firing Button
  • Rectangular Adjustment Buttons
• 0.96 Inch Full Color TFT Screen
  • Displays Essential Data Neatly
    • Check Atomizer
    • Shorted
    • Weak Battery
    • Check Battery
    • Temperature Protected
    • Ohms Too High/ Too Low
    • Too Hot
  • Adjustable via Escribe
• Escribe Companion Software
• Configure and Modify the operation of the DNA 75C
• Micro USB Port
  • 1A Charging
  • Firmware and Software Upgrade
• Stainless Steel 510 Thread Point
• Nickel Plated Brass 510 Contact

Dimensions: 43.5mm*28mm*93mm

In The Box

• 1x Mirage DNA75C Box Mod
• 1x 18650 Battery Adapter
• User Manual
• Warranty Registration Card
• Micro USB Cable

The GBOX bottom feed squonk mod by Geekvape is the latest regulated dual 18650 to hit NZ shores. With 200w maximum output it's designed to be both powerful and reliable, paired with the 8ml squonk bottle and the Radar bottom feed RDA; a brand new rebuildable with a 5ml juice well and unique building posts, the kit delivers ease, convenience and flavour unmatched by tank atomisers

The GBOX is equipped with the AS chipset that is capable of up to 200W and a multitude of functionality. The GBOX has a full temperature control suite, VPC support, and a bypass mode. The GBOX is powered by dual 18650 batteries that are housed through a bottom locking latch door with the 8ml bottom feed bottle. The GBOX can be charged through the USB port up to 2A and utilises the chips smart charging management. The enlarged OLED display is neatly shown on a vertical menu with vape stats including resistance, amps, voltage, puff counter, and battery life.

Along with the GBOX is the Radar bottom feed squonk RDA; a 24mm rebuildable atomiser with a unique dual staggered directional building post. Each posts on the Radar RDA features two terminals that are measured at 3mm in diameter and the coils are held by top mounted Allen screws.

The Radar RDA has a 5mm deep juice well, perfect for dripping or squonking your favourite e-liquid. Airflow enters the Radar through two dual slotted air slots, one measuring at 9.5mm by 2mm, the other measuring at 3mm by 1mm. A 10mm wide bore 810 delrin drip tip comes pre-installed on the Radar but can be switched off with the 10mm 510 delrin drip tip for user preference. With an amazing output and a powerful chipset, the GBOX 200W Kit by Geekvape offers bottom feed users versatility through functionality. 

• 5 to 200W Output
  • GeekVape AS Chip
    
    • Seven Total Output Modes
  • 0.05 to 3.0 ohm Atomizer Resistance Range
  • 0.1 to 8 Voltage Range
  • 0.96" Display Screen
• Temperature Control Suite
  • Ni200 Nickel Support
  • Titanium Support
  • SS316 Support
  • Kanthal Support
  • POWER Support
  • VPC Support
  • Bypass Mode
• Sliding and Locking Bottom Battery Access Door
  • Accepts Dual 18650 Battery (sold separately)
• Enlarged OLED Display
  • Amp Range
  • Output Power
  • Atomizer Resistance
  • Battery Life Indicator
  • Puff Counter
  • Neatly Displayed
• Zinc and Aluminum Materials
• 8ml Squonk Bottle Juice Capacity
  • Bottom Feed Bottle Can Be Removed From the Bottom Battery Access Door
• Micro USB Port
  • Charges upto 2A
• Spring Loaded Gold Plated 510 Connection
  • Hexagon Shaped
• Low Voltage/Current/Output Short Circuit/Load/Low Resistance/Overheating

Radar RDA

1x 510 Delrin Drip Tip
Spare Parts Pack
1x USB Cable
User Manual

The SMOK ProColor 225W is the latest device from SMOK to hit NZ and follows up two of the best selling vape kits and mods in New Zealand - the Alien 220W and T-PRIV 220W.

The Procolor features 225W of power, three output modes and upgradeable firmware. Front OLED screen displays essential information to the user and LED lights on device make for a unique user customisation. 12 light colour options - cyan, white, rainbow, red, green, blue, yellow, magenta, pink, violet, orange and RGB, can be programmed for different styles and lengths of time. A comprehensive temperature control suite packs in adjustable TCR as well as preheat function, making the ProColor a complete and versatile platform.

Adjustments are made via two buttons and the squeeze to fire, firing button.

• 6 to 225W Power Output
  • 0.5 to 9.0V
  • 0.1 to 3.0Ω Atomiser Resistance Range
  • Three Setting Output Mode
    • Hard
    • Normal
    • Soft
  • Firmware Upgradeable
• Temperature Control Output
  • Ni200 Nickel Support
  • Titanium Support
  • Stainless Steel Support
  • Adjustable Initial Resistance
  • Adjustable TCR
  • Preheat Capability
  • 200 to 600 degree Fahrenheit Output Range
  • 0.06 to 3.0Ω Atomiser Resistance Range
• Front Mounted OLED Screen
  • Vibrant Display Resolution
  • Icon Based Display Matrix
    • Highly Visible
    • Comprehensive Menu Settings and Adjustment
    • Full Display
    • Dual Battery Life Indicator
• Dual Adjustment Buttons
• LED Lights On Device
  • 12 Colors
    • Cyan
    • White
    • Rainbow
    • Red
    • Green
    • Blue
    • Yellow
    • Magenta
    • RGB
    • Orange
    • Pink
    • Purple
  • Different Light Display Styles
    • Normal
    • Fade
    • Flash
  • Various Allowed Time
    • Always On
    • Screen On
    • While Vaping
    • Off
• Innovative and Ergonomic Firing Mechanism
  • Comfortable and Easy to Use
  • Squeeze to Fire Operation
• Hinge and Lock Battery Access Door
  • Accepts Two High Amperage 18650 Battery Powered
  • Spring Loaded Internal Contacts
• Zinc Alloy Chassis
• Stainless Steel 510 Threading
  • Gold Plated 510 Contact

ProColor Dimensions:

• 85mm by 46mm by 29.5mm

1x USB Charging Cable
User Manual

Vaporesso introduces their new flagship platform, the Revenger 220W Kit and it's just be delivered to us in NZ! Utilising the latest OMNI Board 2.0 chipset, the Revenger has a 5 to 220W output range, a 0.05 to 5.0Ω atomiser resistance range, and several output modes, two of which include: Customized Curve of Wattage (CCW) and Customized Curve of Temperature (CCT), giving the device much functional versatility.

The Revenger 220W TC device is powered by two 18650 batteries (find them here: Batteries) which can be accessed via the magnetised battery door. A 0.96 inch OLED screen displays essential information to the user such as: wattage/temperature, atomiser resistance, individual battery life display, and also has a Real Time Clock (RTC) display.

The screen itself blends in to the panel, giving the device a unique and classy look. Along with the aluminum alloy chassis material, Vaporesso introduces an In-Mould Labeling (IML) Injection Coating, which is environmentally friendly and allows for greater quality graphics than traditional decorating methods. The Revenger can be charged via USB and has the capability of a 2.5A quick charge, alongside a balancing charge system and USB input protection.

• 5 to 220W Output
  • OMNI Board 2.0
    • Six Total Output Modes
  • 0.05 to 5.0Ω Atomizer Resistance Range
  • 0 to 8.5V Voltage Range
  • Smart VW
    • Automatically Recommend Ideal Output
    • Can Easily Adjust
  • Customized Curve of Wattage (CCW)
    • Customize Wattage Output By Second Increments
    • Customize Ramp Up by 0.5 Second Increments
  • Bypass Mode
  • Firmware Upgradeable
• Temperature Control Suite
  • Ni200 Nickel Support
  • Titanium Support
  • SS316 Support
  • Customized Curve of Temperature (CCT)
    • Customize Temperature Output Over Time
  • TCR Mode
  • 200 to 600 Degrees Fahrenheit
  • Atomizer Lock
• Magnetized Battery Bay Access
  • Dual 18650 Battery Powered
• Sleek and Beautiful Chassis Design
  • Futuristic Styling
• Four Button Control
  • Enlarged Firing Button
  • Angular Adjustment Buttons
  • Mode Button
• 0.96 Inch OLED Display
  • Temperature Mode and Output
  • Output Power
  • Atomizer Resistance
  • Individual Battery Life Indicator
    • Remaining Charging Time (RCT)
  • Puff Counter
  • Real Time Clock (RTC) Setting
  • Screen Blends in to Panel
• 2.5A Quick Charge System
  • Remaining Charging Time
  • Equalizing Charge System
  • USB Input Protection
• Micro USB Charging Port
• In-Mould Labeling (IML) Injection Coating and Aluminum Alloy Chassis
• Spring Loaded Gold Plated 510 Connection
• Low Voltage/Current/Output Short Circuit/Load/Low Resistance/Overheating/Anti Loaded/Timeout Protection

Dimensions

• 45mm by 89mm by 28mm

In The Box

CKS have teamed up with legendary asMODus to bring you one of the most beautiful regulated single 18650 mods on the market. Complete with a marble finish with classy gold trimmings, it’s sure to catch the eye of passersby.

Featuring a vivid colour display on it’s spacious OLED screen, it makes this premium box mod a pleasure to navigate. With an output power range of 5.0 - 80.0 watts, it’s one of the best middle-watt devices on the market. Inside is one of asMODus’ renowned regulated chips giving this beauty astonishing battery efficiency.

The Stride requires one 18650 battery. We recommend the Samsung 25R or Samsung 30Q for this device.

• Output Power Range: 5 - 80 Watts
• Continuous Output Current: 15 - 20 Amps
• Atomiser Resistance Range (power modes): 0.1 - 3Ω
• Atomiser Resistance Range (temperature modes): 0.1 - 0.5Ω
• Battery Input Voltage Range: 3.3 - 4.2 Volts
• Conversion Efficiency: 93%
• Bright Screen Current: 0.3mA
• Shutdown Current: 0.3mA
• Overtime
• Screen Set
• Mode Set
• Puff Counter
• Temperature Control
• Font Colour Control
• Background Colour Control

In The Box
1x CKS x Asmodus Stride 80W Mod
Instruction Manual

The 200W dotBox is now available online and at our vape NZ stores in Wellington and Petone! The dotMod dotBox V2 delivers the perfect combination of power and comfort in a sleek, trim chassis made from anodised aluminum that houses dual 18650 rechargeable batteries.

A unique and stylish mod, the 200W dotBox features dotMod’s proprietary purpose-built dotChip microprocessor that eliminates slow charging, reliability issues, and slow wattage ramp-up found in other processors.

Power inside and out. dotmod’s dotChip microprocessor eliminates slow charging, reliability issues, and the slow wattage ramp-up found in other vape boxes. The powerful chip-set ensures the highest performance, reliability, and functionality on the market.

The dotBox dials everything to 11.

• New Power Curve Mode For Exceptional Output Control
• Dual 18650 Power Source
• 200 Watt Maximum Power Output
• 0.08-3.0Ω Operational Range
• Proprietary DotChip Technology 
• Power Locking Capabilities 
• Auto Timeout Button Lock 
• Multiple Temperature Control Settings
• 24K Gold Plated buttons, Firing Pin And 510 
• Magnetic Door
• Plastic Encased Chipset
• Beveled Edges 
• All Anodised Design 
• Precision Micro-Engraved DotMod Door Logo
• Lightweight And Durable Aluminum Chassis

Batteries not included

The Lost Vape Triade DNA250 Box Mod with two leather options has just landed at The Vape Shop NZ! It's one of the first platforms to fully integrate Evolv's DNA 250 chipset, representative of the most powerful and sophisticated DNA ever created, in the critically acclaimed chassis of the Triade platform.

Evolv's DNA250 is the current flagship from a line-up widely considered to be the most advanced and sophisticated chipset manufacturer today, featuring a tremendous output range from 1 to 250w with an industry leading 97% power efficiency rating. Coupled with the extended output range is the benchmark in Temperature Controlled output, with near limitless support and configurations available when used with the companion Escribe application. The result is the ultimate in output technology that combines efficiency, range, versatility, and customisation.

Surrounding the DNA250 chipset is Lost Vape's Triade platform that aesthetically features a distinct and elegant combination of high end materials and accenting. Machined out of die cast zinc alloy, the main chassis features a sturdy and appealing look, with accented leather battery door trim for an added feel of luxury.

The Triade DNA250 is powered by three 18650 batteries run in series (high amperage batteries sold separately) and are loaded through the battery access door. Through the DNA250's sophisticated balance charger, users are able to directly charge loaded batteries at a maximal rate of 2A, making it an ideal platform for power users on the go. A near irresistible and unmatched blend of aesthetics, ergonomics, range, versatility, power and sophistication, the Lost Vape Triade DNA250 Box Mod is the premiere device for power users and enthusiasts.

Please Note: Batteries must be matched in brand, model and battery state at all times. Discharge and recharge batteries within the same grouping of three. Failure to do so may result in injury. Never use damaged or improperly wrapped batteries with this device.

• Triple 18650 Platform
• Spring Loaded Negative Contacts
• Gold Plated Contacts
• Die Cast Zinc Alloy Chassis Construction
• Solid and Durable Feel
• Leather Paneled Battery Door In Two Colour Options
• Dual Magnetised
• Three Button Control Face
• Lost Vape Preset Escribe Settings
• Stainless Steel 510 Thread Point
• Spring Loaded Nickel Plated Brass 510 Connection

Dimensions
88mm by 50mm by 40mm

Evolv DNA250
1 to 250W Output Range
1 to 9.3V Output
0.1 to 2.0 ohm Kanthal Resistance Range
0.08 to 1.0 ohm Temperature Sensing Range
Cell by Cell Monitoring
Cell Balancer
1A USB Charger
Atomizer, Weak Battery, Temperature, Resistance, Auto Power Down, and Heat Protection
Escribe
Configure and Modify the operation of the DNA200
Escribe Download Link
Escribe Interactive Training Course
Auto-sensing Temperature Resistance
Lock Mode
Stealth Mode
Power Lock Mode
Power Preset Mode
Resistance Lock
Max Temperature Adjustment
Efficiency: 97%
Output Current Continuous Max: 50A
Output Current Instantaneous Peak: 55A
Input Voltage: 9 to 12.6V
Input Current: 0.5 to 28A
Screen On Current: 21mA
Quiescent Current: 3.5mA
Power Down Current: 5uA

1x USB Cable

Lost Vape's EPetite DNA60 Box Mod has just landed in NZ. A new refresh of one of the most beloved box mod designs released in the upscale market. Integrating Evolv's new DNA60 Chipset, an ultra sophisticated platform capable of 1 to 60w, inside a high quality chassis that utilises luxury materials. The EPetite is manufactured with a die cast zinc alloy frame, providing a high level of durability while maintaining a light and well balanced weight distribution. 

The DNA60 inside is one of Evolv's newest single battery chipsets capable of an output of 1 to 60w and near limitless customisation when utilising with the companion Escribe app. Powering the EPetite DNA 60 is a single high amperage 18650 battery (sold separately), that can be charged within the device using Lost Vape's custom 2A charging system that greatly minimises downtime.

The Evolv 0.91 inch display screen is positioned within a cutout in one of the panels, while Lost Vape's signature high grade waterproof buttons are arranged in a classic manner on the control face. The fusion of high quality manufacturing, luxury material paneling, and Evolv's newest single battery chipset, Lost Vape firmly asserts itself atop the upscale DNA box mod market.

• DNA60 Chipset
• 1 to 60w Output
• Escribe Compatible
• Temperature Control Suite
• Ni200 Nickel Support
• Titanium Support
• Stainless Steel Support
• Additional Settings Configured Through Escribe
• Zinc Alloy Chassis
• Compact Design
• Die Cast
• Removable Magnetic Face Panels
• Single 18650 Battery Powered
• Dual Magnetic Battery Access Panel
• Gold Plated Contacts
• Battery Ejection Ribbon
• Three Button Control Face
• 0.91 Inch OLED Display Screen
• Displays Essential Data Neatly
• Escribe Companion Software
• Configure and Modify the operation of the DNA 60
• Escribe Interactive Training Course
• Micro USB Port
• 2A Charging
• Stainless Steel 510 Threading
• Nickel Plated Brass Spring Loaded Contact Pin

Evolv DNA60
1 to 60W Output Range
1 to 9V Output
22A Max Continuous Current
0.25 to 3.0 ohm Kanthal Resistance Range
0.15 to 1.0 ohm Temperature Sensing Range
Cell Balancer
Atomizer, Weak Battery, Temperature, Resistance, Auto Power Down, and Heat Protection
Escribe Download Link
Escribe Interactive Training Course
Autosensing Temperature Resistance
Lock Mode
Stealth Mode
Power Lock Mode
Power Preset Mode
Resistance Lock
Max Temperature Adjustment
Efficiency: 85%
Screen On Current: 26mA
Quiescent Current: 7mA
Power Down Current: 0mA

Lost Vape Epetite DNA60
73mm x 45mm x 27mm

In the box
1x Lost Vape EPetite DNA60
1x Micro USB Cable
User Manual

The Therion DNA166 by Lost Vape, where Evolv's dynamic DNA250 chip combined with Lost Vape's superior chassis design and ergonomics come together to create an absolutely stunning device.

Featuring Evolv's newest chipset, the DNA250, the power of the Therion DNA166 has been throttled down to 166 Watts for this two cell configuration.

Featuring a curved design for a better hand feel and aesthetically pleasing design choices, no shortcuts have been taken to ensure a comfortable vaping experience. Tasteful dark wood accents come together with genuine leather to develop awe-inspiring eye candy. The leather wrapped battery panel is secured with a magnet and a ball bearing design which creates a strong bond but also provides an ultra smooth pull when replacing the two 18650 batteries this device requires (sold separately).

The button design has seen a slight redesign from being the traditional circular buttons to now a more angular shaped button that fits the overall appearance of the Therion. High grade stainless steel makes up the 510 threads while the spring loaded plated brass 510 pin is plated for maximum conductivity. From elements of a high powered chip to stylish accents and exceptional building materials, Lost Vape has perfected the DNA166 mod with the Therion.

We recommend the Sony VTC5A be used with the Therion DNA166. Purchase them here: Sony VTC5A

• Die cast zinc alloy
• Laser etched logo
• Spring loaded stainless steel 510 connector
• Smart OLED display with intuitive menu
• Built with Evolv DNA 250 chip
• Energy efficiency: 85%
• Power output range: 1W to 166W
• Temperature control: 200°F to 600°F or 100°C to 300°C
• Temperature control lowest resistance: 0.08Ω
• Power mode lowest resistance: 0.15Ω
• Temperature control is compatible with SS, Ni and Ti
• Uses two 18650 batteries (sold separately) 
• Parallel battery installation
• USB charging
• Programmable multi-color LED indicator
• Customise via Escribe software
• USB firmware upgrades
• Short circuit protection
• Low voltage protection
• Cell by cell monitoring
• Cell balancing
• Overheat protection

Dimensions: 27 mm x 90.5mm x 54mm
Weight: 380g

In the box
1x Lost Vape Therion DNA166
1x USB Cable
1x English User Manual